OLICOM, INC. OC-3230 TR/MODEM 144 Card Type Modem(asynchronous), Fax, NIC Chip Set Texas Instruments TMS 380C25 Maximum Onboard Memory 32KB, 128KB for LAN buffers Network Rate 4/16Mbps Maximum Data Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Bus PCMCIA Type II Fax Class Class I & II Data Modulation Protocol Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis Fax Modulation Protocol Unidentified Error Correction/Compression MNP10, V.42bis Topology Token Ring Wiring Type Shielded/Unshielded twisted pair Boot ROM 128KB PROM V1802/N1433 Proprietary AT Command Set AUTO-RETRAIN - FALLBACK/FALLFORWARD Type: Configuration Format: AT [cmds] %E n [cmds] Description: Controls auto-retrain mode and fallback/fall forward. Command Function %E0 Auto-retrain disabled %E1 Auto-retrain enabled %E2 Auto-retrain and Fallback/fall forward enabled %E3 Auto-retrain and Fallback/fall forward with fast hang up enabled BREAK SEND Type: Configuration Format: AT [cmds] \B n [cmds] Range: 1-9 Unit: .1 second Description: Sends break of n to modem BREAK TYPE Type: Configuration Format: AT [cmds] \K n [cmds] Description: Configures action of break signal Command Break from DTE Modem receives Break from \B remote modem Reliable/Normal mode \K0 Enter command mode, Buffers Buffers do not send break to cleared and cleared and remote modem. break sent to break sent to remote modem. DTE. \K1 Buffers cleared and Buffers Buffers break sent to remote cleared and cleared and modem. break sent to break sent to remote modem. DTE. \K2 Enter command mode, Send break to Send break to do not send break to remote modem DTE remote modem. immediately. immediately. \K3 Send break to remote Send break to Send break to modem immediately. remote modem DTE immediately. immediately. \K4 Enter command mode, Send break to Break sent do not send break to remote modem with received remote modem. with data to the transmitted DTE. data. \K5 Send break with Send break to Break sent transmitted data. remote modem with received with data to the transmitted DTE. data. CELLULAR TRANSMISSION LEVEL Type: Configuration Format: AT [cmds] @M n [cmds] Default: Unidentified Range: 0 - 31 Unit: -1 dBm Description: Sets the signal level for transmission when in leased line mode CHANGE COUNTRY CODE Type: Configuration Format: AT [cmds] *NC nn [cmds] Description: Changes country code to one of 8 stored in NVRAM COMPRESSION Type: Configuration Format: AT %C n Description: Selects data compression. Command Function %C0 Data compression disabled %C1 MNP5 enabled %C2 V.42bis enabled %C3 MNP5 and V.42bis enabled COMPROMISE EQUALIZER Type: Configuration Format: AT [cmds] :E n [cmds] Description: Controls compromise equalizer Command Function :E0 Equalizer disabled :E1 Equalizer enabled CONNECT MODE Type: Configuration Format: AT [cmds] \N n [cmds] Description: Sets connect mode Command Function \N0 Normal mode enabled \N1 Direct mode enabled \N2 Reliable mode enabled \N3 Auto-reliable mode enabled \N4 LAPM mode only enabled \N5 MNP mode only enabled DISPLAY CURRENT CONFIGURATION Type: Immediate Format: AT [cmds] \S [cmds] Description: Displays current command profile DISPLAY DELAYED NUMBERS Type: Immediate Format: AT [cmds] *B [cmds] Description: Displays list of delayed numbers DISPLAY DELAYED NUMBERS Type: Immediate Format: AT [cmds *D [cmds] Description: Displays list of of delayed numbers DISPLAY LINE SIGNAL LEVEL Type: Immediate Format: AT [cmds] %L [cmds] Description: Displays received line signal level in dBm DISPLAY LINE SIGNAL QUALITY Type: Immediate Format: AT [cmds] %Q [cmds] Description: Displays line signal quality DISPLAY STORED NUMBERS Type: Immediate Format: AT [cmds] \F [cmds] Description: Displays all stored phone numbers FALL-BACK Type: Configuration Format: AT [cmds] -Q n [cmds] Description: Enables fall back to V.22/V.22bis Command Function -Q0 V.22/V.22bis fall back enabled -Q1 V.22/V.22bis fall back disabled FLOW CONTROL Type: Configuration Format: AT [cmds] \G n [cmds] Description: Enables modem port flow control Command Function \G0 Flow control disabled \G1 Flow control enabled LOCK SERIAL PORT Type: Configuration Format: AT [cmds] \J n [cmds] Description: Sets operation of serial port speed Command Function \J0 Serial speed locked \J1 Serial speed follows connect speed MAXIMUM MNP BLOCK Type: Configuration Format: AT [cmds] \A n [cmds] Description: Sets the maximum transmission block size Command Function \A0 MNP block size is 64 characters \A1 MNP block size is 128 characters \A2 MNP block size is 192 characters \A3 MNP block size is 256 characters MNP10 COMPRESSION Type: Configuration Format: AT [cmds] -K n [cmds] Description: Selects MNP10 data compression Command Function -K0 MNP10 disabled -K1 MNP10 enabled MNP 10 HANDSHAKE Type: Configuration Format: AT [cmds] *H n [cmds] Description: Selects MNP 10 link negotiation speed Command Function *H0 MNP 10 handshake at highest common speed *H1 MNP 10 handshake at 1200bps *H2 MNP 10 handshake at 4800bps MNP10 POWER LEVEL ADJUST Type: Configuration Format: AT [cmds] )M n [cmds] Description: Controls automatic transmit power level adjustment during MNP 10 link negotiation Command Function )M0 Power level adjustment disabled )M1 Power level adjustment enabled MNP STREAM/BLOCK MODE Type: Configuration Format: AT [cmds] \L n [cmds] Description: Selects the transfer mode for MNP Command Function \L0 Stream mode for MNP enabled \L1 Block mode for MNP enabled PROTOCOL/SPEED Type: Configuration Format: AT [cmds] F n [cmds] Description: Selects protocol and line speed used Command Function F0 Select fastest common protocol F1 V.21/Bell 103A F3 Not used F3 V.23 F4 V.22/Bell 212A 1200bps F5 V.22bis 2400bps F6 V.32bis/V.32 4800bps F7 V.32bis 7200bps F8 V.32bis/V.32 9600bps F9 V.32bis 12.0Kbps F10 V.32bis 14.4Kbps PULSE DIAL CODE Type: Configuration Format: AT [cmds] *Z n [cmds] Description: Selects digit used for pulse dial code Command Function *Z0 Use dial code 0 *Z1 Use dial code 1 REMOTE CONFIGURATION PASSWORD Type: Configuration Format: AT [cmds] *C n [cmds] Description: Store remote configuration password REMOTE MNP Type: Configuration Format: AT [cmds] *R [cmds] Description: Requests remote modem’s MNP configuration SETUP PASSWORD Type: Configuration Format: AT [cmds] *P xxxx / yyyy [cmds] Description: Changes the modem’s password and callback number. xxxx represents the password, and yyyy represents the callback number. V.23 SPLIT BAUD MODE Type: Configuration Format: AT [cmds] \W n [cmds] Description: Controls V.23 split baud mode Command Function \W0 V.23 split baud mode disabled \W1 V.23 split baud mode enabled VIEW DATA Type: Configuration Format: AT [cmds] %F n [cmds] Description: Selects split transmit and receive line speeds during viewdata operation Command Function %F1 75bps transmit/1200bps receive when viewdata selected %F2 1200bps transmit/75bps receive when viewdata selected S REGISTERS Register Function Default S14 Bit mapped Unidentified S16 Bit mapped test options Unidentified S20 Bit mapped Unidentified S21 Bit mapped Unidentified S22 Bit mapped speaker Unidentified options S23 Bit mapped Unidentified S24 Sleep inactivity timer 0 S27 Bit mapped Unidentified S28 Bit mapped Unidentified S29 Flash modifier timer 0 S31 Bit mapped Unidentified S33 XOFF character 19 S40 Bit mapped Unidentified S41 Bit mapped Unidentified S80 Soft switch Unidentified S99 Leased line transmit Unidentified level S201 Cellular transmit level Unidentified S202 Remote escape character Unidentified